Why Understanding Essential Plumbing Skills is Crucial For Installing a Bathtub
Why Understanding Essential Plumbing Skills is Crucial For Installing a Bathtub
Blog Article
Just how do you really feel about How to Install a Bathtub Yourself?
Setting up a bath tub isn't precisely brain surgery, but it does need strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bath tub with a new one is also a moderately hard job. If the old tub is easily obtainable, the project can move speedily; if you need to open up a wall to get rid of the old tub as well as place the new bathtub, the job is much harder. In either case, the task is within a residence handyman's skills, although you will certainly need an assistant to move out the old bathtub and embeded in the new one. See to it you have actually certified yourself for the work as well as fit attempting it. Instead of hiring a contractor to take control of a halfway-completed task, it is much better to consider utilizing one prior to you begin. Possibilities are you might need an expert plumber to make tube connections.
This post will certainly assist you set up a brand-new bathtub in your shower room if you have actually currently bought a new tub as well as don't need to transform the setup of your previous water system pipes.
Your devices as well as product list must make up the following:
Preparing for the Installment
First of all, the sustaining frame provided with the bath needs to be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps system to avoid pressure on the bath tub.
Fit the flexible tap adapters to the bottom of both faucets utilizing 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final setting.
Removing Old Touches
If you need to change old faucets with new ones as a part of your setup, after that the first thing you should do is disconnect the water system. After doing so, turn on the taps to drain any kind of water remaining in the system. The process of removing the existing faucets can be rather troublesome because of the restricted gain access to that is usually the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a towel all set for the staying water that will come from the pipelines. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old securing substance.
Before carrying on to fit the brand-new faucets, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Installing the Bathtub
Using both wooden boards under its feet, place the bath tub in the needed setting. The wooden boards are helpful in uniformly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by examining the spirit level as well as adjusting the feet on the bathtub till the level reviews level.
To install taps, fit all-time low of the outermost adaptable faucet connector to the appropriate supply pipeline by making a compression sign up with; after that do the same for the other tap.
Switch on the water system and examine all joints as well as new pipework for leakages as well as tighten them if required. Fill the bath tub as well as likewise inspect the overflow electrical outlet and the regular electrical outlet for leaks.
Lastly, deal with the bath paneling as defined in the supplier's instruction manual. Tiling and also securing around the bath tub ought to wait till the bath tub has been used at the very least once as this will settle it into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will require a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the faucet in the placing hole in the bath/basin guaranteeing that the washing machines are in area between the faucet and also the sink. Protect the faucet in place with the maker provided backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous kind should be linked to the faucet ends first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bath satisfies the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to fracture an inflexible seal, causing the water to pass through the wall between the bathroom and also the tiling, resulting in issues with wetness and possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures as well as installations. They are offered in tubes and also cartridges, and are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of drenched newspaper or soft rope. Remember to always fill the tub with water before sealing, to allow for the activity experienced when the tub remains in use. The sealer can break relatively very early if you do not take into account this activity before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also quickly offered on the marketplace. It is advisable to fit the floor tiles utilizing water-resistant or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed our post about Tools You Need to Install a New Bathtub . Thanks so much for finding the time to browse our content. Appreciated our write up? Please share it. Let other people check it out. I am grateful for your time. Don't hesitate to visit our blog back soon.
Request our service. Report this page